50v-1000v 2.0a surface mount fast recovery rectifiers e-mail: sales@taychipst.com web site: www.taychipst.com 1 of 2 rs2a thru rs2m f eatures for surface mounted application glass passivated junction chip built-in strain relief, ideal for automated placement plastic material used carries underwriters laboratory classification 94v-o fast switching for high efficiency high temperature soldering: 260 / 10 seconds at terminals m echanical data cases: molded plastic terminals: solder plated polarity: indicated by cathode band packing: 12mm tape per e1a std rs-481 weight: 0.093 gram maximum ratings and electrical characteristics rating at 25 o c ambient temperature unless otherwise specified. single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% type number symbol rs 2a rs 2b rs 2d rs 2g rs 2j rs 2k rs 2m units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified current see fig. 1 @t l =100 o c i (av) 2.0 a peak forward surge current, 8.3 ms single half sine-wave superimposed on rated load (jedec method ) i fsm 50 a maximum instantaneous forward voltage @ 2.0a v f 1.3 v maximum dc reverse current @ t a =25 o c at rated dc blocking voltage @ t a =125 o c i r 5 200 ua ua maximum reverse recovery time ( note 1 ) trr 150 250 500 ns typical junction capacitance ( note 2 ) cj 50 pf typical thermal resistance (note 3) r ja r jl 55 18 o c /w operating temperature range t j -55 to +150 o c storage temperature range t stg -55 to +150 o c notes: 1. reverse recovery test conditions: i f =0.5a, i r =1.0a, i rr =0.25a 2. measured at 1 mhz and applied v r =4.0 volts 3. thermal resistance from junction to ambient and junction to lead mounted on p.c.b. with 0.4? x 0.4? ( 10mm x 10 mm ) copper pad areas.
surface mount fast recovery rectifiers e-mail: sales@taychipst.com web site: www.taychipst.com 50v-1000v 2.0a 2 of 2 rs2a thru rs2m tj=125 c 0 tj=2 5 c 0 fig.6 - revers e recove r y tim e characteristi c an d tes t circui t diagram 50 noninductive non inductive oscilloscope (not e 1) pulse gener a t or (not e 2) dut (+) 50vdc (approx) (-) notes : 1 . ris e t ime=7n s max . inpu t impedance= 1 megoh m 22pf 2 . ris e t ime=10n s max . sours e impedance= 5 0 ohms (-) (+) 10 noninductive -1.0a -0.25a 0 +0.5a trr 1cm set time base for 5/ 10ns/ cm fig.2- typical reverse characteristics instantaneous reverse current .( a) 0 20 40 60 80 100 120 140 percent of rated peak reverse voltage. (%) 0.1 1 10 100 fig.5- typical instantaneous characteristics forward instantaneous for ward current . (a) 0.6 0.8 1.0 0.4 1.2 1.4 1.6 1.8 0.1 0.01 1 10 20 forward voltage. (v) pulse width=300 s 1% duty cycle tj=25 c 0 fig.4- typical junction capacitance junction cap acitance.(pf) 1 10 100 10 90 reverse voltage. (v) tj=25 c f=1.0mhz vsig=50mvp-p 0 550 50 fig.1- maximum forward current derating curve average for ward current . (a) 50 60 70 80 90 100 110 120 140 130 150 160 0.5 1.0 1.5 2.0 lead temperature. ( c) o resistive or inductive load p.c.b. mounted 0.4 x 0.4" ( 10 x 10mm ) copper pad areas 2.25 fig.3- maximum non-repetitive peak forward surge current peak for ward surge current . (a) 1 10 100 0 40 10 20 30 50 number of cycles at 60hz tl=100 c 8.3ms single half sine wave jedec method 0
|
